PDA

View Full Version : diesel install?



jcbarton
01-07-2009, 04:43 PM
Once you install a cell on a diesel engine how do you go about reducing the diesel consumption and using the HHO? I understand the concept on gasoline engines with carbs. and fuel injected (re-jetting the carb/EFIE/MAP/MAF'S etc.) but I don't know much about diesel set-ups. Is there an electronic device needed or something like re-jetting the carb?? Thanks.

hydrotinkerer
01-08-2009, 11:20 AM
It will work the same on a gas engine with a carb(w/out jet changes), You won't need to push the acc. as hard to do the same amount of work. That is the short version.

water4gasinstaller
01-08-2009, 12:05 PM
We did install diesel engines from 1 tonne , 3 tonne and 11 tonne trucks, well they work pretty fine if you have a HHO Unit that runs and generates lots of HHO. Well we attached a 12volt unit for 1 tonne, whereas the 3 tonne and 11 tonne truck we attached a 24 volt. the two models generates large amounts of HHO. HM160 generates 160 liters and HM240 generates 240 liters. This baby gave 27% till 40% mileage gain. no kidding. however you need a auto cut off swtich we call ACOS because if you leave the keys on for half an hour, your intake manifold along with your air filter will blow up to pieces! no kidding

HM160 looks like this (picture and video)
http://www.water4gasinstaller.com/index.php/Hydrox-Mobile-HM160.html

HM240 looks like this (picture and video)
http://www.water4gasinstaller.com/index.php/Hydrox-Mobile-HM240.html

Auto Cut Off Switch (ACOS) looks like this (picture and video)
http://www.water4gasinstaller.com/index.php/Auto-Cut-Off-Switch-ACOS.html

tracker
03-20-2010, 09:20 PM
Is this real ..... 160 lpm on 14 amps ???

N11634
03-20-2010, 10:31 PM
I'm hoping that's per hour. That would translate to about 2.6 LPM.

lhazleton
03-21-2010, 01:18 AM
If you look at their info, it's 160LPH, which is 2.6LPM. Pretty good for 15 amps, but I'm willing to bet that there's lots of steam.

GEDRUS
10-31-2012, 08:45 AM
We did install diesel engines from 1 tonne , 3 tonne and 11 tonne trucks, well they work pretty fine if you have a HHO Unit that runs and generates lots of HHO. Well we attached a 12volt unit for 1 tonne, whereas the 3 tonne and 11 tonne truck we attached a 24 volt. the two models generates large amounts of HHO. HM160 generates 160 liters and HM240 generates 240 liters. This baby gave 27% till 40% mileage gain. no kidding. however you need a auto cut off swtich we call ACOS because if you leave the keys on for half an hour, your intake manifold along with your air filter will blow up to pieces! no kidding

HM160 looks like this (picture and video)
http://www.water4gasinstaller.com/index.php/Hydrox-Mobile-HM160.html

HM240 looks like this (picture and video)
http://www.water4gasinstaller.com/index.php/Hydrox-Mobile-HM240.html

Auto Cut Off Switch (ACOS) looks like this (picture and video)
http://www.water4gasinstaller.com/index.php/Auto-Cut-Off-Switch-ACOS.html


Where to get that switch, please add link, thanks....