PDA

View Full Version : pwm for big blocks



redfred
09-11-2012, 08:44 AM
I have a 5.3L chevy that I'm putting in HHO. I've already installed but not made final connections of 2 wet cells with 11 plates measuring 2 3/8" X 4 1/4". I also have an EFIE and a Scan Gauge. Ive read in different places that i need a PWM to prevent over heating. Do I need a PWM for each cell and at what amperage size for it(them)? And What gauge wire to make connection? Also what is a good brand or model and the place to buy?

Thanks

philc1974
09-12-2012, 08:29 AM
HI there

Not sure about the wet cell, but you should consider a dry cell set-up as it will be more efficient, easier to manage and produce more HHO.

The hotter the water gets the more the amp draw in a dry cell, this is where the PWM comes in, it will stop the thermal runaway.

Another solution to the thermal runaway problem, and i can confirm this ACTUALLY works, is to restrict the water flow from the reservoir going directly into the dry cell, restricting the flow will not only reduce amp draw, and stop the water reaching 70 degrees c but also, reduce the amps and voltage needed to produce the same amount of HHO.

Ive tried it, it really works!

Shane Jackson
09-15-2012, 09:03 AM
Think about what you said.... and think about what is going on in the cell. Here's a clue "produce the same amount of HHO." can you say STEAM!




Another solution to the thermal runaway problem, and i can confirm this ACTUALLY works, is to restrict the water flow from the reservoir going directly into the dry cell, restricting the flow will not only reduce amp draw, and stop the water reaching 70 degrees c but also, reduce the amps and voltage needed to produce the same amount of HHO.

Ive tried it, it really works!

Madsceintist
09-15-2012, 07:48 PM
HI there

Not sure about the wet cell, but you should consider a dry cell set-up as it will be more efficient, easier to manage and produce more HHO.

The hotter the water gets the more the amp draw in a dry cell, this is where the PWM comes in, it will stop the thermal runaway.

Another solution to the thermal runaway problem, and i can confirm this ACTUALLY works, is to restrict the water flow from the reservoir going directly into the dry cell, restricting the flow will not only reduce amp draw, and stop the water reaching 70 degrees c but also, reduce the amps and voltage needed to produce the same amount of HHO.

Ive tried it, it really works!

Whoa Kemosabe,
1; If you slow the water down to the "dry" cell you will actually create thermal runaway and steam, as you will have too many bubbles in the cell and not enough cooling from the water.
2; Also, "wet" and "dry" cells can create around the same amount of HHO and quality. However "dry" cells are a little more effiecent as the flow of water helps to push the bubbles from the surface to free up room for the next .

Keep it cool and keep the flow going !

redfred
09-19-2012, 05:50 PM
where can you buy a good PWM? Ive heard about PWMs that will power 2 cells, anyone know about these or can 2 cells be powered by one PWM?

Hydrogen Tech
12-21-2012, 09:07 PM
Yes, it is possible to run two cells (wet or dry) off of one PWM. Take a look at http://www.hydrogentech.co/shop/category/ccpwm/

They sell Constant Current PWM's, if you want one send me an Email and I'll send you a coupon code.

If you need a wiring diagram or explanation for wiring 2 cells to one PWM, let me know. I am an electrical engineer and can help you with that.

http://www.hydrogentech.co/

http://www.youtube.com/watch?v=OqbHIbYGIuE&feature=player_embedded