+ Post New Thread
Page 11 of 47 FirstFirst ... 9 10 11 12 13 21 ... LastLast
Threads 201 to 220 of 922

Forum: Q & A

This section is for Questions and Answers.

  1. What IS the proper number of plates?!?!?!?

    so it seems clear that more plates equals greater efficiency in a dry cell. But when does this stop? Im about to put together my stack with 6 nuetral...

    Started by aceras624‎, 02-22-2012 12:14 AM
    • Replies: 3
    • Views: 834
    02-22-2012, 03:53 AM Go to last post
  2. How long does it take it to see gas production on the first run?

    I just ran my first dry cell for the first time. It's been about five minutes and I've only seen a few small bubbles. It's a single stack, +NNNNNN-...

    Started by fluttercell‎, 02-20-2012 11:16 PM
    • Replies: 3
    • Views: 648
    02-21-2012, 11:58 PM Go to last post
  3. dry cell crapped out!!! why?!?

    so Ive been running my prototype HHO dry cell for about a week now and all of a sudden the amperage it pulls is like HALF and its getting HOT(not the...

    Started by aceras624‎, 02-16-2012 03:14 AM
    3 Pages
    1 2 3
    • Replies: 20
    • Views: 2,659
    02-20-2012, 03:17 PM Go to last post
  4. Results - Check Engine Light ?

    Info: - 2005 Dodge grand caravan - homemade 6x6 21 plate dry cell -nnnn+nnnn-nnnn+nnnn- - 2lpm, 11.2v, 28A = MMW 6.377 - NaOH 1Tbs to a gallon ...

    Started by witmeraa‎, 03-24-2011 11:12 PM
    3 Pages
    1 2 3
    • Replies: 24
    • Views: 4,205
    02-19-2012, 06:26 PM Go to last post
  5. How to calculate amount of KOH needed?

    I don't remember enough of chemistry to remember how to calculate masses needed for certain concentrations of solutions. So, I know I need a 24% KOH...

    Started by fluttercell‎, 02-11-2012 09:04 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 2,831
    02-16-2012, 08:13 PM Go to last post
  6. HH and O separeted

    Hello folks. Are there any cell designs which will produce HH and O, so that we don't need to inject the O part in the engine any more? For those...

    Started by WorstCases‎, 02-13-2012 11:20 PM
    • Replies: 5
    • Views: 950
    02-16-2012, 01:14 AM Go to last post
  7. plate count

    I have my first dry cell done .Seems to work great after some experimenting and advise from you guys.Heres the design.+nnnn-nnnn+nnnn-.My question is...

    Started by danntanna‎, 02-12-2012 04:53 PM
    • Replies: 9
    • Views: 1,293
    02-15-2012, 04:10 AM Go to last post
  8. Lightbulb Will MAF sensor combust HHO inside intake chamber?

    In prereration for HHO installation I modified my intake. I have a 1999 Toyota 4Runner 3.4L. I can route the HHO into the intake either before the...

    Started by GDTRFB85‎, 05-26-2008 01:21 AM
    • Replies: 8
    • Views: 2,872
    02-14-2012, 01:04 AM Go to last post
  9. which is a better way?

    Im wondering if it is better to add KOH to my dry cell until I can pull the amps I want or should I max the ammount of KOH and use my PWM to stop the...

    Started by aceras624‎, 02-13-2012 05:24 AM
    • Replies: 2
    • Views: 927
    02-13-2012, 10:11 PM Go to last post
  10. What happens to the NaOH electrolyte

    So, im curious - we add lots of electrolye to the dist. water. What ends up happening to all the NaOH, does it just build up on the dry cell plates...

    Started by Alkaline‎, 02-08-2012 05:39 PM
    • Replies: 7
    • Views: 1,217
    02-09-2012, 06:00 AM Go to last post
  11. Angry Did I wire the cell up wrong ? Please help !!!

    Again here is my configuration, / ----------/-----------/ ----------------- to one 12v power source +nnnn-nnnn+nnnn-nnnn+ 21 plate ...

    Started by Donor‎, 02-06-2012 05:29 PM
    • Replies: 2
    • Views: 930
    02-08-2012, 10:40 PM Go to last post
  12. Very low yield (first HHO dry cell attempt)

    Currently using the + n n n n n - n n n n n + config with 1/16" 316 steel plates (4"x6") and 1/16" rubber spacers. Alternator putz out 14.2v or...

    Started by Alkaline‎, 02-08-2012 02:31 AM
    • Replies: 3
    • Views: 1,333
    02-08-2012, 02:31 PM Go to last post
  13. Nothing.

    I just installed my 21 plate drycell. -nnnn+nnnn-nnnn+nnnn- It is 6x6 with the bolt holes on the outside of the cells versus in the middle of the...

    Started by Donor‎, 02-04-2012 04:33 AM
    • Replies: 5
    • Views: 1,109
    02-05-2012, 02:55 AM Go to last post
  14. Formula for how much hho is needed?

    What is the formula for knowing how much hho is needed for a particular engine? I have a 3.3L fuel injected V6 Nissan Xterra 2003.

    Started by TimCollins‎, 09-14-2011 04:43 AM
    • Replies: 5
    • Views: 2,378
    01-31-2012, 12:16 PM Go to last post
  15. Too many amps?

    I have a 9-plate dry cell, with plates cut to 6x6 inches and with about 1/2 inch gaskets for each side, making about 25 square inches of sanded...

    Started by cpaiin‎, 01-29-2012 04:50 AM
    • Replies: 7
    • Views: 1,455
    01-31-2012, 06:08 AM Go to last post
  16. Question QUICK stupid ? before puttin togather

    Just want to make sure ALL plates have a top and bottom hole. My bottom holes will be staggered left to right. Want to put this togather tonight.

    Started by Donor‎, 01-27-2012 11:33 PM
    • Replies: 2
    • Views: 764
    01-28-2012, 01:53 AM Go to last post
  17. 2002 S10 Extreme LS 4.3

    I'm running a 16 plate cell and a quad digital EFIE. I'm curious if anyone knows what the readings should be for the the oxygen wire and the computer...

    Started by bilkster55‎, 01-15-2012 06:51 AM
    • Replies: 6
    • Views: 1,606
    01-23-2012, 02:15 AM Go to last post
  18. california emissions

    I have a question, how does a vehicle with a hho booster, and a efei get a smog check here in califonia? Anyone that has experienced this I would...

    Started by rodbolt100‎, 01-21-2012 02:35 AM
    • Replies: 4
    • Views: 1,354
    01-21-2012, 08:27 PM Go to last post
  19. New Project Diesel Truck Hyundai HD-65 no gains

    Hi guys, I have installed 3 dry cell systems to 3 of my trucks. They are Hyundai HD-65 4Cilinders in-line 3.5L I run an 18 plates dry well with...

    Started by francodrr‎, 01-19-2012 02:20 PM
    • Replies: 0
    • Views: 760
    01-19-2012, 02:20 PM Go to last post
  20. Volo and chip question

    Why do some systems like the one sold by the mileage shop say they do not require an Efie or volo.

    Started by Joedirt1‎, 01-14-2012 11:36 PM
    • Replies: 1
    • Views: 865
    01-19-2012, 01:31 PM Go to last post

+ Post New Thread

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts