I am rebuilding an old dry cell. The plates I have are actually in very good shape but I am wondering if anyone has suggestions of how best to clean these before I rebuild them into a new cell? ...
Type: Posts; User: TimCollins
I am rebuilding an old dry cell. The plates I have are actually in very good shape but I am wondering if anyone has suggestions of how best to clean these before I rebuild them into a new cell? ...
I am rebuilding my old dry cell. I had used clear acrylic case material but I ran into a problem where it was kind of thin and would sometimes crack. I do like being able to see the through the...
Ah yes... Great idea... I know exactly what you are talking about and I think it would work well. Thanks for the response...
This looks like an old post but i posed a question about how to do this here: http://www.hhoforums.com/showthread.php?8346-Seperating-Hydrogen-and-Oxygen
It is an idea I have but have not tested......
How are folks creating gaskets for dry cells? Is there something commercially available that you can use to cut to fit? I have used an old farm tractor tire inner tube to create gaskets and that...
Anyone near Ft Lauderdale experimenting with HHO? I am just looking for any local contacts of others working on this project...
Can someone point me to the formula for how many neutral plates I should have between charged plates for a SS 21 plate dry cell? My plates are approximately 8” x 8”. However, my gaskets are...
I would like to set up my test bench to run my cell for some time. Are there any good commercially available power supplies to use for this? I tried using a battery for a while but it discharges...
I am interested in separating the Hydrogen and Oxygen after it has been produced. I saw a couple of posts but my idea on the topic is a little different than the posts about using membranes … I...
I replaced my old dishwasher this weekend. I am curious about the SS it contains. The door and all the interior are SS. I have no clue about its grade or gage although I am sure it is not 18. Is...
So, some mechanism showing HHO filling a basic two liter bottle is this forums' standard quo test for lpm?
Provided we also show reasonable evidence that the gas is not water vapor I'm not exactly...
I have seen youtube videos of folks that have basically submerged two liter bottles and filled them with HHO gas to measure lpm. Is that a fair test? Is there a better way to test lpm?
At what amperage should I become concerned that my Nissan Xterra 3.3L V6alternator may become over stressed? Right now I am just workbench testing so nothing is actually installed. I want to test...
WOW what a thread… I do see validity in one of his points. To ‘prove’ HHO introduction into the fuel system by itself has any ‘real’ effect at all (good or bad) we have to perform a...
I found some time to workbench test run my generator for the first time today. I only ran it for about 15 minutes outside just to be safe... It went well for what little I did and I have a couple...
I read your line "water input is approx 3x as restrictive as gas output *or greater". I take this as meaning that your electroltye input connection to your generator is three times smaller than your...
Is it better to keep KOH stored in the container it comes in, or is it ok to go ahead and measure it out and store it in zip lock bags?
You might get a laugh out of this... I got some time this afternoon to mix some electrolyte. Not thinking much about it.... I poured precisely 5oz of KOH into 50oz of H2O for a 10% mixture into a...
Once KOH is disolved in water will it stay in solution long term or will it precipitate if it is not shaken regularly?
My math here has to be wrong?? I will try to keep this short... My setup is a simple dry cell 21 plates SS with 1/16" separation. Each plate has an active surface area of about 6.5"x6.5". Here is...
I received my KOH 'Caustic Potash Potassium Hydroxide' and I am wanting to try out my generator for the first time. The generator is NOT installed in my truck. I will be running it on my workbench....
Please click one of the Quick Reply icons in the posts above to activate Quick Reply.
It seems like one of the variables has to be conductivity of the solution. I dont know if there is such a table for example conductivity of KOH (if thats what you are using) in water at certain...
Anyone in Ft Lauderdale / Miami Area working on HHO projects?
I was looking around on the net for where to get some electrolyte (locally in Ft Lauderdale / Miami area). I found a reference 'you can get NaOH at Lowe's, under the name "Roebic crystal drain...