Search:

Type: Posts; User: nikolatesla

Search: Search took 0.00 seconds.

  1. Replies
    159
    Views
    312,460

    Sticky: Thanks, I'm running 25-35 amps depending on the...

    Thanks,
    I'm running 25-35 amps depending on the engine rpm ..at idle the volts are lower .

    I aproximate my reading by blowing up balloons with a stopwatch and doing a volume calculation

    I...
  2. Replies
    159
    Views
    312,460

    Sticky: Thanks for that, I was under the distinct...

    Thanks for that,

    I was under the distinct impression that I would see an increase because of the better burn .
    Timing will be difficult to tamper with but I will investigate the ways to to do it...
  3. Replies
    159
    Views
    312,460

    Sticky: toyota landcruiser 4.5 litre straight 6 aussie version

    Hi all,

    First I want to thank everyone for the kind help here .
    I have installed my hho system and run it for 3 tanks of fuel (petrol)
    I have found no difference but I will explain the setup...
  4. Replies
    5
    Views
    6,227

    It this an add?? If so please give all of the...

    It this an add??

    If so please give all of the details like milage claims and show your test results for us .

    my air conditioner has been running in my landcruiser for 200 thousand miles but it...
  5. Replies
    12
    Views
    11,080

    It may be that the alluminium /stainless contact...

    It may be that the alluminium /stainless contact area will be a problem in the long run.
    I dont know if any body has tried it yet. or if not why not . As the conduction, both electrical and heat...
  6. Replies
    12
    Views
    11,080

    Like this with positive in the middle and...

    Like this with positive in the middle and negative at each end
  7. Replies
    12
    Views
    11,080

    No They are not in contact with the solution but...

    No They are not in contact with the solution but are flat against the last cell ss plate at both ends al ss-nnnnn+nnnnn-ss al . There is no way I would use alloy as a cell plate , just a good...
  8. Replies
    12
    Views
    11,080

    OOPS ,sorry I was not clear at all I used...

    OOPS ,sorry I was not clear at all
    I used alluminium for the end clamp plates ,the cell plates are stainless, but and are in contact with the external heavy alluminum on each end allowing quite a...
  9. Replies
    12
    Views
    11,080

    Good point, Im using the transmission switch...

    Good point,
    Im using the transmission switch output in the center console mechanically attached to the handle which is 12 v high in drive . I aslo powers the D light on the dashboard . Ill use a...
  10. Replies
    12
    Views
    11,080

    Thanks biofarmer , Ok then my setup will be...

    Thanks biofarmer ,

    Ok then my setup will be with it pre air cleaner for a few thousand kilometeres.

    If i dont get results I will change it and see ...heck, I will probably change it and see...
  11. Replies
    12
    Views
    11,080

    HHO pre air cleaner newbie

    Hi again everybody,
    I'm at 3rd base with my first system and planning on injecting pre air cleaner.

    Im gertting 1 lpm for about 18 amps -nnnnn+nnnnn- 6"x6" plates ,diamond oreintation. cell temp...
  12. Replies
    0
    Views
    7,122

    Glue for sodium hydroxide

    Hi all,
    I have just got to first base with my first cell .

    Im down under and it is going in a 105 4.5 l pertrol landcruiser.
    I am using a slotted no holes design that I think is my own.
    In the...
  13. Replies
    7
    Views
    6,818

    Thanks Gentlemen This might be fun I like...

    Thanks Gentlemen

    This might be fun
    I like "dry edged fuel burner"
    or "skeptik magnet"
    even " arrogance tester"
    better "ignorange blaster"
    how about " recirculating under bonnet fuel...
  14. Replies
    8
    Views
    12,405

    It is called entertainment it is entertainment...

    It is called entertainment it is entertainment and they are very funny sometimes ....please dont expect there to be anything important revealed by these bufoons . Their main source is movie myths...
  15. Replies
    7
    Views
    6,818

    Slotted design and a newbie question

    Hi everyone ,this is my first post and I would like to thank you all for being so helpful as I build my first serious generator.

    I am heading down the path of a slotted box design with no plate...
Results 1 to 15 of 15