Search:

Type: Posts; User: TACAMO

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    5,070

    Ohh sorry 49 plates,...

    Ohh sorry 49 plates, -NNNNN+NNNNN-NNNNN+NNNNN-NNNNN+NNNNN-NNNNN+NNNNN-, running off car battery.
  2. Replies
    5
    Views
    5,070

    All right, 50 plate, -NNNNN+, not sure on the...

    All right, 50 plate, -NNNNN+, not sure on the spacing, 8 gauge wire, sodium hydroxide
  3. Replies
    5
    Views
    5,070

    Good Production, But a lot of heat!!!

    hi, My dry cell production is just where I want it, But it gets hot fast. Is there any way of cooling it with out lowing my electrolyte mix. Would a PWM help? It runs at 23 amps 12v.
  4. Replies
    1
    Views
    3,422

    Best torch plate config.

    Hey, What do you all think would be the best configuration for a torch?

    13.6 volt: +NNNN-NNNN+NNNN-NNNN+NNNN-NNNN+ or

    120 volt: +(44 Neutrals)-
  5. Thread: PWM not working

    by TACAMO
    Replies
    0
    Views
    3,547

    PWM not working

    Hi, I bought a PWM online, Worked great until I fried the output transistors. I replaced the two transistors with 4 IRF510 transistors. after this it worked better than the original. Today I was...
  6. Thread: Wow!!!! How!!!

    by TACAMO
    Replies
    0
    Views
    2,833

    Wow!!!! How!!!

    hi, its me again. I saw this on youtube http://www.youtube.com/watch?v=jU5RETtCsSQ I almost have the same setup(Cell Wise). My plates aren't as close as his, but dang. how is he getting so much...
  7. Replies
    3
    Views
    4,212

    cool, Thanks. Scratch the relay. I went...

    cool, Thanks. Scratch the relay. I went with 4 IRF510 MosFets(all radioshack had)
  8. Replies
    3
    Views
    4,212

    New PWM Realy vs Transistors

    hey, I just fried my PWM. I'm going to build a new one using a 555 IC. What would work better, having the 555 switching 4 High power 2N3055 transistors, or switching a high power relay.
  9. Thread: My First Cell

    by TACAMO
    Replies
    4
    Views
    5,576

    Thanks man this forum is great. I'm building...

    Thanks man this forum is great. I'm building this just to experiment and learn a little and yes see the bubbles. I don't plan of putting this in a car or anything, I just like to make things. I...
  10. Thread: My First Cell

    by TACAMO
    Replies
    4
    Views
    5,576

    My First Cell

    Hey, Just wanted to share my first Cell, I am makeing 3 of these. Each are 20 Stainless Steel washers. Connected in +-+-. Running them off a 12 volt 35 amp power supply through a PWM. Just finished...
  11. Thread: Pipe Cell

    by TACAMO
    Replies
    2
    Views
    4,731

    Pipe Cell

    Hi, I want to make the pipe cell, A pipe within a pipe. I have quit a bit of galvanized steel pipe. Will this work.
  12. Thread: First Time Help

    by TACAMO
    Replies
    2
    Views
    4,212

    Cool Tanks for the quick replay. This whole...

    Cool Tanks for the quick replay. This whole HHO gas thing is so cool. Why is this not everywhere
  13. Thread: First Time Help

    by TACAMO
    Replies
    2
    Views
    4,212

    First Time Help

    HI, I just built my first HHO Cell. How do I hook up my multimeter to see how many amps i drawing. Cant figure it out, always read Zero.
Results 1 to 13 of 13