Check this site out. It is plans to build a Geet system for a small engine.
Know where does it say to use a magnet for the rod. It only says that the
engine must be oriented so as the reaction...
Type: Posts; User: dixiepc
Check this site out. It is plans to build a Geet system for a small engine.
Know where does it say to use a magnet for the rod. It only says that the
engine must be oriented so as the reaction...
The rod is not a magnet to start with. When you start the engine for the first time you make sure that the rod is aligned north and south then when the motor is started it magnetizes the rod. Don't...
Gus,
What's up with the BioBeast?
Water is composed of 2 parts hydrogen and 1 part oxygen. You are always going to make twice the amount of hydrogen as oxygen. No more no less.
Is there not someone close to you that could sandblast your plates fo you?
Alright Ben, since you are ready to share your bubbler design with us, we are ready for you to share your bubbler design with us.
Shoot!
It's a 6.2L diesel.
My breather is the type that is on top of the engine. Do you think that the ozone generator could be mounted under the lid inside the breather with a hole to the outside for the air going into the...
I have a 6.2L diesel. Diesels don't have a whole lot of vacuum. Would the air flow through the breather be enough. This is a totally mechanical engine.
When using these ozone generators, how do you introduce the ozone into the system? Would you happen to have any pictures of this setup?
You should not be using baking soda, it puts out a poisonous gas. You should be using KOH or NaOH. There is a forum here on the best electrolytes.
Check out the BioBeast Progress thread in the general discussion section. If you read all that it should answer all your questions.
Gus,
What's happening with the Beast?
OK, my next question is about the number of bubblers. Gus, did you ever determine, for sure, that if the first and last plate of each group were the same polarity, that it would negate the need for...
Sorry Gus, I edited my post to use the correct terms. Now that I have got that part straight in my brain I will move on to other questions later.
Monty
So each group will be making 1.29 lpm at 18 amps for a reactor total of 9.03 lpm at 126 amps. Right?
Carter,
Is it a good thing or a bad thing for the cell to run in the flooded state?
Monty
OK Gus here we go again,
If I build a build a unipolar cell in this configuration []+ - + - + [] + - + - + [] + - + - + [] + - + - + [] + - + - + [] + - + - + [] + - + - + [] with 9 square inches...
Wow Gus, you really busted my bubble. I thought I was getting close to understanding what I was doing. I was going from what I thought (LOL) I read in the amperage thread. Guess I'll take this new...
Gus, do I look like I'm in the ball park with my figures?
Monty
If I build a unipolar cell in this configuration []+ - + - + - + [] + - + - + - + [] + - + - + - + [] + - + - + - + [] + - + - + - + [] + - + - + - + [] + - + - + - + [] with 17.5 square inches of...
How do you get by without a bubbler.
Gus,
I will when I get all my ducks in a row.
I still have some things that I don't throughly understand and don't want to start until I do.
I know that it will not be the license plate...
I want to bring this thread back to life as it is almost exactly what I want to do.
I have a fully mechanical naturally aspirated 6.2L diesel in a 1992 Suburban.
Gus, would you offer me the...
I think that the license plate cell is a good idea. The cell will be wider than tall so the bubbles might go out faster. Also there will be alot of surface area per plate so maybe I can get the...