Search:

Type: Posts; User: velorossa22

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    4,239

    Roll of 316L Stainless Plate annealed

    I bought this awhile ago and made some plates from it. Had the idea that I was going to make more to sell but I ran out of time awhile ago. Should be still about 80' left on the roll. I have the...
  2. Replies
    5
    Views
    12,816

    Never heard of them before. The idea of platinum...

    Never heard of them before. The idea of platinum and palladium is for catalytic convertors: Here's a description of how it works:
    The oxidation catalyst is the second stage of the catalytic...
  3. Replies
    7
    Views
    6,306

    Does the wire to your cell heat up? If it gets...

    Does the wire to your cell heat up? If it gets hot its adding resistance to your circuit and could cause voltage drop at the cell. If your voltage is dropping throughout the car then you may have...
  4. Replies
    1
    Views
    3,855

    What reservoir size are people using

    I was wondering what you all were using for sizes on electrolyte reservoirs? I was using 2" x 12" ABS tubing. I found I could use less KOH that way. But thinking later I'm thinking that my high...
  5. Replies
    3
    Views
    7,883

    yeah I kind of thought that thinner metal...

    yeah I kind of thought that thinner metal shouldn't make much of a difference. I haven't ever hard any warp on the metal parts just on the 1/2" plexiglass end plates. I did have pitting though when...
  6. Replies
    3
    Views
    7,883

    26ga SS 316 too thin?

    Just wondering if anyone has used such thin stainless for their cells ( or even used thinner). I'm not sure why thinner metals would make much of a difference in production but would save money. ...
  7. Replies
    14
    Views
    15,940

    What size coil weight and thickness are you...

    What size coil weight and thickness are you usually buying? Is the metal hard to get to flatten out of the coil or does it flatten easy?
  8. Replies
    4
    Views
    5,611

    Also make sure your connections are tight. Loose...

    Also make sure your connections are tight. Loose connections cause heat as well.
  9. Replies
    39
    Views
    27,337

    So is your cell consuming the same amount of...

    So is your cell consuming the same amount of amperage whether it works or it doesn't? I had an issue with heat that would cause slight warping after a longer run and it would start shorting plates...
  10. Replies
    34
    Views
    36,563

    Qhack! I wonder if the reason you are getting...

    Qhack! I wonder if the reason you are getting such a mileage difference is the difference in the pump itself. I would imagine that every pump has a different place where it clicks off to say it's...
  11. Replies
    4
    Views
    4,818

    Make sure that the cell is getting a good amount...

    Make sure that the cell is getting a good amount of airflow. I've seen many setups near the radiator to get maximum air flow. One of the main disadvantages of wet cell is the heat produced. You...
  12. Replies
    2
    Views
    4,881

    HHO Dry Cell 9 Plate KIT $68.99???

    So there is a kit on ebay that says they have 316L SS plates. The plates are fairly small (3.5 x3.5) but still that seems really cheap. Do you guys think that this kit is for real? It just seems...
  13. Replies
    24
    Views
    14,938

    Here's one for $65 includes shipping...

    Here's one for $65 includes shipping...
  14. Replies
    24
    Views
    14,938

    Biggy Boy how much are you seeing the EGTs...

    Biggy Boy how much are you seeing the EGTs selling for? You should check them out on ebay, they look legit and they are less than $100. Unless that's too much for you :eek:
  15. Replies
    6
    Views
    7,522

    If you are scared about leaning out too much one...

    If you are scared about leaning out too much one way to monitor is using a EGT ( exhaust gas temp sensor). Getting a baseline of average exhaust temperatures w/o modification will give you numbers...
  16. Replies
    2
    Views
    4,679

    Before you do any leaning I would definately...

    Before you do any leaning I would definately install an exhaust gas temp sensor that way you won't be as likely to damage the motor.
  17. Replies
    8
    Views
    10,102

    yeah I looked it up and it basically computes out...

    yeah I looked it up and it basically computes out to L x rpm. Even if you divide it by 5 ( since you're feeding close to 100 % O2 instead of 20% in regular air) you're still way short.
  18. Replies
    8
    Views
    10,102

    I was thinking about it, about how many lpm do...

    I was thinking about it, about how many lpm do car's use for air volume. If you could figure out how much your car uses at WOT you could regulate the amount of hho to regular incoming air and make...
  19. Replies
    12
    Views
    9,853

    Cool design Qhack. This would be a really good...

    Cool design Qhack. This would be a really good test to see. If you can't get significantly better mileage from this then we are barking up the wrong tree!
  20. Replies
    12
    Views
    9,853

    Do you think the 2 bubblers are removing most of...

    Do you think the 2 bubblers are removing most of the contaminants? Obviously one is not doing the trick.
    I really want to believe in the dry cell, but so far I haven't seen anyone get much...
  21. Replies
    12
    Views
    9,853

    So are you saying that possibly the increase in...

    So are you saying that possibly the increase in mileage on the w4g designs and wet cell designs might be due to water vapor? If so that might make a some sense.
    How are you keeping KOH and NaOH out...
  22. Replies
    7
    Views
    6,985

    Word of warning! For some reason my cell was...

    Word of warning! For some reason my cell was creating throttle issues. I don't know why exactly but after leaving the cell off for a week the car seemed to return back to normal, but when I...
  23. Replies
    12
    Views
    9,853

    Thanks for the input. Qhack I am ordering a EGT...

    Thanks for the input. Qhack I am ordering a EGT as I'm afraid to modify the AFR much without it since I don't have a car I can sacrifice right now. I'm not giving up quite yet on dry cells, but...
  24. Replies
    7
    Views
    6,248

    How are you guys checking cell temps? Also how...

    How are you guys checking cell temps?
    Also how are you using stainless end plates without causing dead short? I like the idea but not sure how to put it into effect.
    I've been using 1/2...
  25. Replies
    12
    Views
    9,853

    This is frusterating

    So I've been using my dry cell on my 96 subaru with no positive results. I get consistantly the same mileage with and without my cell. What's worse is after 400 miles it starts to gum up my...
Results 1 to 25 of 92
Page 1 of 4 1 2 3 4