Gary,
That's a nice drawing. It shows that you know what you're doing and have a great attitude about "getting it right."
I see two changes I'd recommend. First, because of the pulsing action...
Type: Posts; User: astrocady
Gary,
That's a nice drawing. It shows that you know what you're doing and have a great attitude about "getting it right."
I see two changes I'd recommend. First, because of the pulsing action...
Most foaming is caused by contamination. You have to be very careful when you assemble your unit that your plates are perfectly clean.
Try draining you system and flushing it with distilled...
It's only my opinion, but I think you'd be better off with an EFIE than the Volo chip. I tried one and never could get any results until I switched to an EFIE. Mind you, I only tried the Volo on...
It appears that you are not producing near enough HHO for that size of engine. A 4 liter engine will require 2 lpm of HHO. To produce that much HHO a resonably effecient electrolize will require 30...
It was kind of a bust, IMO. There were 7 exhibitors and that all there was to the show. Each exhibitors was to give a 1-2 hour seminare. Since I didn't find out about this until that morning, and...
So now we know what you think of us... SPAM! HUH!!!
I can see where you would be right if you made modification to the injection timing as such. The problem I see with that is that if for some reason you had to shut down the HHO for some reason (or...
Vistor,
The arrestors have one or more very fine plastic screens. They are not homemade. They come in different sizes for different throughput. Contace Bruce directly through the email seller...
OK -- I'm not an EFIE expert either, but I think I know what is going on. I assume you're using a FuelSaver-MPG analog narrow band EFIE.
If you put your meter between the two test probe ports on...
borescopeit,
You are right about the placebo effect. That does enter into play. And there is the other side of that effect --- the driver notices more power and keeps check that on each start-up...
That is the company I work for, only before I came on-board and completely redesigned their system -- LOL. Like I said, I've personally never gone, and the guys that displayed at that show are no...
Sniper,
It sounds like you have your EFIE set to high -- you are trying to lean your fuel too much. During the first half of the tank, the computer and EFIE are fighting and then finally the...
No, I have no idea who delvis11 is. I sometimes go by HydroSysSteve on other forums.
Larry, I hear you loud and clear and agree 1000%! I had several threads bookmarked so I could refer to that information. Now it's gone. From now on, I guess I'll print them and start a file ---...
Ooooops! I made a type! the above should have read...
A GOOD flashback arrestor is needed, though, and should NOT cause a drop in production.
These are the arrestors I use......
Well, I was totally shocked and depressed to see the Underground shut down. I don't think Nick realized the impact the site was making. I don't post much, but I read almost everything and will miss...
Sounds like you're progressing nicely. A little back pressure, below 3 psi, shouldn't hurt anything and shouldn't affect production. I personally don't think you need a check valve, especially...
The Yaris has a 1.5 liter engine, the same engine that was in the Scion Xa and first generation Xb. The same engine was also used in the toyota echo and the pree-2010 Prius, plus a TON of toyotas...
MAF is not an O2 Sensor. It is a Mass Air Flow sensor.
Most gasoline engines built after the late 80's have at least one O2 sensor, which is always located in the exhaust. Most cars built...
Since the O2 sensor is located in the EXHAUST, I don't think you want to inject the HHO AFTER the O2 Sensor. Big Bang.
I think what you meant, was after the MAP/MAF sensor in the air intake.
I...
witmeraa,
Congratulations! It sounds like you've built yourself a nice system. But, there is always a but, there are a couple of suggestions I'd like to make.
First, you say you can see the...
I think you're all over reacting. I use one, well designed (IMO) bubbler utilizing a porous plastic aerator and I can see no signs of vapors coming out, even when running at 4 lpm. I've directed...
That's good to know, Ben. I will probably still try it if the volo by itself doesn't work, only because I would be putting an EFFIE on anyway, so the only real difference would be when I disconnect...
Sounds like a good test. I am also testing a volo chip on my wife's 205 KIA Spectra w/2.0L engine. I installed the hho system and the chip at the same time. I know HHO works, so I didn't feel the...
If a cell produces at least 1 lpm (that's dry gas, after passing through an effective bubbler scrubber to remove all water vapor) for every 15 amps at average automobile voltage of 13.5 volts, it's a...