Search:

Type: Posts; User: mauroalpha

Search: Search took 0.00 seconds; generated 35 minute(s) ago.

  1. Replies
    24
    Views
    26,887

    I'm back with some new info after testing for a...

    I'm back with some new info after testing for a while.

    1) Using pump will help to produce more hho gas

    2) For have more gas with less amp my solution is to have the right mix of
    distilled...
  2. Replies
    6
    Views
    9,656

    Ciao Tim, for me the best way to separate H from...

    Ciao Tim,
    for me the best way to separate H from HHO is to find something that adsorb Oxygen like a sponge, for release it in another chamber...or something that adsorb oxygen in a reaction without...
  3. Replies
    24
    Views
    26,887

    Ciao Jason, I've solved the flux problem changing...

    Ciao Jason, I've solved the flux problem changing the stack configurations of the cell.

    So about the stack, I've discovered that if I use 3 Neutral, my psu doesn't work at 12v but at 10.xx and...
  4. Replies
    0
    Views
    13,656

    OXYHN new gas

    hey folks,
    just browsing the videos i've discovered this one

    http://www.youtube.com/watch?v=F0GCRPQAdmc

    they are using water plus 3 normal products that all have at home for clean..

    what's...
  5. Replies
    24
    Views
    26,887

    thanks, i've ordered the dc lcd from china..i...

    thanks, i've ordered the dc lcd from china..i think i will receive in 3 weeks and then get u back :)
  6. Replies
    24
    Views
    26,887

    Ok I mounted all with new pwm. same as last...

    Ok I mounted all with new pwm.
    same as last time, if 12 volt is set, i obtain that the cell adsorb 25 amp but 7,22 volt. If I keep controlled the voltage and i push up the pwm, the voltage goes to...
  7. Replies
    24
    Views
    26,887

    No, I told 6 gap cause for 5 plates I mean...

    No, I told 6 gap cause for 5 plates I mean 5neutral :)
  8. Replies
    24
    Views
    26,887

    i made a mistake, 5 plates = 6 gap so the volts...

    i made a mistake, 5 plates = 6 gap so the volts are less

    this night i will use my new pwm so i will get u back with results
  9. Replies
    24
    Views
    26,887

    myoldyourgold (what's your real name?): at the...

    myoldyourgold (what's your real name?):

    at the moment I've ordered the new psu 12v 50amp, and a new PWM made by the dealer
    (it's an electronic engineer that is working on water engine for boat) ...
  10. Replies
    24
    Views
    26,887

    Ciao Pete, the cable that I use are 4mm wires...

    Ciao Pete,

    the cable that I use are 4mm wires ; after 10 minutes of uses without pwm my psu got warm and then burnt out :( this is my 4 psu that get burnt without pwm..I don't understand why!!! ...
  11. Replies
    24
    Views
    26,887

    update

    thanks mate for the tip :)

    So,
    this night I ran my pwm at maximum (the pwm knob is not at its maximum but less than half, is correct?) and I haven't seen the previous production observed at that...
  12. Replies
    4
    Views
    23,324

    Havens, can u post the pics here please? :)

    Havens, can u post the pics here please? :)
  13. Replies
    24
    Views
    26,887

    uhm, what is its name in english ? gripper ? i...

    uhm, what is its name in english ? gripper ?
    i will search here :)

    So, yesterday I've tried my re assembled cell and it's gone. I have 5 cm flame with 20 amp , cell configuration is +NNN- (I've...
  14. Replies
    24
    Views
    26,887

    myoldyourgold: thanks for your suggest, this...

    myoldyourgold: thanks for your suggest, this morning I've disassembled my cell and I've put the inlet under the outlet and this evening I will post the result;
    I've also used another water tank, a...
  15. Replies
    24
    Views
    26,887

    Hy guys, yes water should come from the bottom of...

    Hy guys, yes water should come from the bottom of the tank and then it turn up;

    so it's very important the tank size and the pressure of the water inside?I was thinking that the only important...
  16. Replies
    24
    Views
    26,887

    improving flux and suggest

    Hi guys,
    I'm italian and I'm trying to build my hho heater;I've a 25 plates dry cell that was sold to me has 3,2 lpm at 25amp 12v.
    So, I'm using 14mm hose with Rilsan connection and a mini water...
Results 1 to 16 of 16