Ive been running two systems along side of each other from the same battery source seperate reserviors, and ive found that running one system produces better results. The power from the 100 amp...
Type: Posts; User: Jamesleaper
Ive been running two systems along side of each other from the same battery source seperate reserviors, and ive found that running one system produces better results. The power from the 100 amp...
ive got no intention of doing this myself, i am still not sure if my vehicle is electronic or mechanical. I spoke to my mechanic today about retarding the pump, (as my vehicle was in for its yearly...
I was about to have my pump retarded by one degree, but then thought, doesn't the fuel have to be reduced to match the increase in hho supply. Not knowing how that is done, are the two done at the...
just wondered, how often do you change the rice?
Have a look any comments , let me now, jim
http://youtu.be/Vzbaj0jkq5M
:D
You mention the "fuel screw", ive looked up the bosch pump which i believe to be fitted to my vehicle.
http://gnarlodious.com/vanagon/bosch_pump/Bosch_VE_Pumps.pdf
what is the fuel screw, or...
Are you saying i need to use a thicker gasket i.e. 2mm? and if that is the case, as i have enough 1mm gasket material spare would doubling up be ok. thanks jim.
Can you please take a look at the video and results and pass comment if you think there is a problem or not. thanks jim.
http://youtu.be/B_jmtSVSaVU
Just wondered, what is the affect on the running of the engine if the pump is retarded 1 degree and the HHO stops working, does the engine stop working or is it starved of fuel at high revs? or...
Can you take a look at the video and tell me if i am doing it right? also should the readings just keep and climbing?
http://youtu.be/1MHqof69HEl
a second relay might be a good idea, that would determine if one or the reactor does or doesnt work.
the following was used for the gasket: purchased on ebay
1mm thick neoprene rubber sheet black 1mtr x 1.4mtrs (170758784847)
and i used this to cover the bolts:
...
Well at the moment the fuse is blowing, so i am going to test across each plate this weekend as suggested. I am not sure what i am looking ie. voltage increase or decrease, and what that would tell...
i was looking at how to retard the diesel pump on you tube, i couldn't find anything for my car, would you say this video is what is involved?, and as a total amateur i would be right in thinking...
so are you saying that because i have an intercooler then it is more than likely i will not get the full benefit of HHO?
or, and i have to make more HHO than i have made so far, and if so how more...
Well drove 2 miles looked under the bonnet/hood and the fuse had blown, washed out mix and changed to water only, must be a lot of residue in the bottom of second rector. Measurents taken with just...
Ok there is a series of videos to watch, unfortunately there isnt a pause button on my phone, hence a few videos.
Ive a question about the intercooler and my connection to the air intake, have a...
Question, i have earthed to the chasis and not the battery, and as yet have no negative connection at all to the battery, other than via the chasis, would a direct connection to the battery improve...
Just bypassed the PWM, however havent changed wire size and took a reading on the ampmeter, no change, so increased amount of KOH, still no change on ampmeter.
Question, Is my wire size, (2.5mm2),...
I agree so why is it working at all?!
Yes i used electrolyte, but i didn't measure quantities or volume of gas, it was more to see it work before fitting it. I am going to video the wiring and...
i added a PWM this build.I think the plates are 1.5mm thick. I will have to measure them.
its solid wire, iam going to change the and see what that achieves.
ok just looked up short circuit, i was thinking, maybe the wire i am using is not heavy duty enough, perhaps i should increase from 2.5mm2 to 4mm2. what do you think?
ok, i need a bit of help here, i dont understand what i should be looking for, a short being metal against metal, and are you thinking that i should be connecting the earth to the battery, are you...
the wire size is 2.5mm2. I also think it may be poor circulation within the unit. I was thinking of adding another set of inlets and outlets on the other face of HDPE.