Search:

Type: Posts; User: astrocady

Page 1 of 10 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    7
    Views
    6,602

    Gary, That's a nice drawing. It shows that...

    Gary,

    That's a nice drawing. It shows that you know what you're doing and have a great attitude about "getting it right."

    I see two changes I'd recommend. First, because of the pulsing action...
  2. Replies
    1
    Views
    3,690

    Most foaming is caused by contamination. You...

    Most foaming is caused by contamination. You have to be very careful when you assemble your unit that your plates are perfectly clean.

    Try draining you system and flushing it with distilled...
  3. Replies
    3
    Views
    6,046

    It's only my opinion, but I think you'd be better...

    It's only my opinion, but I think you'd be better off with an EFIE than the Volo chip. I tried one and never could get any results until I switched to an EFIE. Mind you, I only tried the Volo on...
  4. It appears that you are not producing near enough...

    It appears that you are not producing near enough HHO for that size of engine. A 4 liter engine will require 2 lpm of HHO. To produce that much HHO a resonably effecient electrolize will require 30...
  5. Replies
    14
    Views
    14,326

    It was kind of a bust, IMO. There were 7...

    It was kind of a bust, IMO. There were 7 exhibitors and that all there was to the show. Each exhibitors was to give a 1-2 hour seminare. Since I didn't find out about this until that morning, and...
  6. Replies
    14
    Views
    14,326

    So now we know what you think of us... SPAM! ...

    So now we know what you think of us... SPAM! HUH!!!
  7. Replies
    13
    Views
    11,138

    I can see where you would be right if you made...

    I can see where you would be right if you made modification to the injection timing as such. The problem I see with that is that if for some reason you had to shut down the HHO for some reason (or...
  8. Replies
    28
    Views
    54,372

    Vistor, The arrestors have one or more very fine...

    Vistor,
    The arrestors have one or more very fine plastic screens. They are not homemade. They come in different sizes for different throughput. Contace Bruce directly through the email seller...
  9. Replies
    24
    Views
    19,900

    OK -- I'm not an EFIE expert either, but I think...

    OK -- I'm not an EFIE expert either, but I think I know what is going on. I assume you're using a FuelSaver-MPG analog narrow band EFIE.

    If you put your meter between the two test probe ports on...
  10. Replies
    13
    Views
    11,138

    borescopeit, You are right about the placebo...

    borescopeit,

    You are right about the placebo effect. That does enter into play. And there is the other side of that effect --- the driver notices more power and keeps check that on each start-up...
  11. Replies
    29
    Views
    22,485

    That is the company I work for, only before I...

    That is the company I work for, only before I came on-board and completely redesigned their system -- LOL. Like I said, I've personally never gone, and the guys that displayed at that show are no...
  12. Replies
    24
    Views
    19,900

    Sniper, It sounds like you have your EFIE set to...

    Sniper,
    It sounds like you have your EFIE set to high -- you are trying to lean your fuel too much. During the first half of the tank, the computer and EFIE are fighting and then finally the...
  13. Replies
    28
    Views
    54,372

    No, I have no idea who delvis11 is. I sometimes...

    No, I have no idea who delvis11 is. I sometimes go by HydroSysSteve on other forums.
  14. Replies
    29
    Views
    22,485

    Larry, I hear you loud and clear and agree 1000%!...

    Larry, I hear you loud and clear and agree 1000%! I had several threads bookmarked so I could refer to that information. Now it's gone. From now on, I guess I'll print them and start a file ---...
  15. Replies
    28
    Views
    54,372

    Ooooops! I made a type! the above should have...

    Ooooops! I made a type! the above should have read...

    A GOOD flashback arrestor is needed, though, and should NOT cause a drop in production.

    These are the arrestors I use......
  16. Replies
    29
    Views
    22,485

    Well, I was totally shocked and depressed to see...

    Well, I was totally shocked and depressed to see the Underground shut down. I don't think Nick realized the impact the site was making. I don't post much, but I read almost everything and will miss...
  17. Replies
    28
    Views
    54,372

    Sounds like you're progressing nicely. A little...

    Sounds like you're progressing nicely. A little back pressure, below 3 psi, shouldn't hurt anything and shouldn't affect production. I personally don't think you need a check valve, especially...
  18. Replies
    25
    Views
    31,612

    The Yaris has a 1.5 liter engine, the same engine...

    The Yaris has a 1.5 liter engine, the same engine that was in the Scion Xa and first generation Xb. The same engine was also used in the toyota echo and the pree-2010 Prius, plus a TON of toyotas...
  19. Replies
    11
    Views
    16,327

    MAF is not an O2 Sensor. It is a Mass Air Flow...

    MAF is not an O2 Sensor. It is a Mass Air Flow sensor.

    Most gasoline engines built after the late 80's have at least one O2 sensor, which is always located in the exhaust. Most cars built...
  20. Replies
    11
    Views
    16,327

    Since the O2 sensor is located in the EXHAUST, I...

    Since the O2 sensor is located in the EXHAUST, I don't think you want to inject the HHO AFTER the O2 Sensor. Big Bang.

    I think what you meant, was after the MAP/MAF sensor in the air intake.

    I...
  21. Replies
    24
    Views
    19,900

    witmeraa, Congratulations! It sounds like...

    witmeraa,

    Congratulations! It sounds like you've built yourself a nice system. But, there is always a but, there are a couple of suggestions I'd like to make.

    First, you say you can see the...
  22. Replies
    48
    Views
    39,377

    I think you're all over reacting. I use one,...

    I think you're all over reacting. I use one, well designed (IMO) bubbler utilizing a porous plastic aerator and I can see no signs of vapors coming out, even when running at 4 lpm. I've directed...
  23. Replies
    10
    Views
    12,911

    That's good to know, Ben. I will probably still...

    That's good to know, Ben. I will probably still try it if the volo by itself doesn't work, only because I would be putting an EFFIE on anyway, so the only real difference would be when I disconnect...
  24. Replies
    10
    Views
    12,911

    Sounds like a good test. I am also testing a...

    Sounds like a good test. I am also testing a volo chip on my wife's 205 KIA Spectra w/2.0L engine. I installed the hho system and the chip at the same time. I know HHO works, so I didn't feel the...
  25. Replies
    5
    Views
    10,616

    If a cell produces at least 1 lpm (that's dry...

    If a cell produces at least 1 lpm (that's dry gas, after passing through an effective bubbler scrubber to remove all water vapor) for every 15 amps at average automobile voltage of 13.5 volts, it's a...
Results 1 to 25 of 234
Page 1 of 10 1 2 3 4