Search:

Type: Posts; User: absoluteanc

Search: Search took 0.00 seconds.

  1. Replies
    32
    Views
    19,027

    I found the most accurate information overseas...

    I found the most accurate information overseas with publications like the one you just found. It seems there is an intent to put out inaccurate information that pertains to Hydroxy here in the...
  2. Replies
    6
    Views
    11,814

    Thank you, very helpful

    Thank you, very helpful
  3. Replies
    6
    Views
    11,814

    Best Gasket

    I have looked for EPDM pond liner but it is 40mil at the most. What is the best place to fine a small sheet of 1/16" EDPM. Do you have to order weld on or is it available retail?
  4. Nice clean job. What is the output have you...

    Nice clean job. What is the output have you measured it yet?
  5. Thread: New Design

    by absoluteanc
    Replies
    7
    Views
    8,770

    I wish, one is my 300e and the other is my...

    I wish, one is my 300e and the other is my girlfriends 190e 2.6. Both are great cars mine is 25 years old and runs better than a newer car. Great toys for the car enthusiast.
  6. Thread: New Design

    by absoluteanc
    Replies
    7
    Views
    8,770

    The new cell will be improved with staggered...

    The new cell will be improved with staggered holes on the bottom and media blasting. The new bigger thinner design will hopefully serve two purposes. First would be to cut the shop time considerably...
  7. Thread: New Design

    by absoluteanc
    Replies
    7
    Views
    8,770

    New Design

    Hi I am working on a new design and would rather spend more time on the drawing board than shop time in 105 degree heat. The new idea is to use only 7 cell only and increase the size to 9 x 9 active...
  8. Replies
    57
    Views
    165,063

    Also, I want people to know size DOESNT matter...

    Also, I want people to know size DOESNT matter with HHO cells. I have tested 4", 6" dry cells, and small/large wet cells, and have came to the conclusion that size really doesnt matter

    I am...
  9. Replies
    5
    Views
    5,115

    One big unit or many small units?

    Just wanted to see if anyone has an opinion on better production while using lower amps.

    Is one big dry cell that can handle 60 amps but uses 15 amps better?

    Or many smaller dry cells running...
  10. Replies
    2
    Views
    7,051

    One is a air flow or temp sensor and one is a...

    One is a air flow or temp sensor and one is a breather that recirculates fumes. The rule of thumb is to inject the hydrogen into the air inlet just before the air filter. You could drill a hole in...
  11. Replies
    9
    Views
    7,794

    Weld on 16

    I was curious as to what this weld-on 16 epoxy is used for? Does it seal the threads to prevent leaks on the output side?
  12. Replies
    9
    Views
    7,794

    Solution

    Thanks for the advice let me make sure I am understanding you correctly.

    1 ml of water = 1 gram

    1000 ml water = 200 grams of electrolyte?

    So for 1 gallon (3780 ml) I would need to add 756...
  13. Replies
    9
    Views
    7,794

    Understanding Hydroxy Better

    Hi I am new to the forum and want to share my design for constructive criticism. The dry cell generator is 7 cell, 15 plate configuration per unit (-nnnnnn+nnnnnn-). This is a parallel 7 cell...
Results 1 to 13 of 13