Search:

Type: Posts; User: jbalat

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    5,464

    Gia Sou theodore, You can start by reading.....

    Gia Sou theodore,
    You can start by reading.. There is much to learn and no guarantees at the end.

    Whether you build or buy will depend on your skill and whether you are married or not ;)

    I...
  2. Replies
    1
    Views
    4,949

    Firstly good luck. If you dont succeed in making...

    Firstly good luck. If you dont succeed in making any savings you will still enjoy working on the project, there is so much to learn (I speak from experience)

    The ebay unit looks pretty good if you...
  3. Replies
    3
    Views
    8,240

    David did you say you had a Pajero ?? I have...

    David did you say you had a Pajero ??

    I have been looking for someone who has had positive results on a 3.0L V6

    The best savings I could get was around 13% and it was not repeatable.

    Are you...
  4. Replies
    8
    Views
    9,784

    No, I switched it off for now under the...

    No, I switched it off for now under the assumption I am not feeding my car enough gas. I am making a duplicate unit so I can run 2 in parallel...
  5. Replies
    2
    Views
    5,325

    I must admit I havent measured the Output of the...

    I must admit I havent measured the Output of the cell, I am only estimating but I get your point..

    As for my ecu, Its kind of inbetween. Its MUTII
  6. Replies
    53
    Views
    34,125

    You guys crack me up :eek:

    You guys crack me up :eek:
  7. Replies
    8
    Views
    9,784

    I understand about getting a better flow and I...

    I understand about getting a better flow and I agree. I would like to try snap on pneumatic connectors to make things a little easier. I am currently using garden connectors which are very bulky.
    ...
  8. Replies
    8
    Views
    9,784

    Thanks lhazleton, for now I was just going to...

    Thanks lhazleton,
    for now I was just going to add another plate to each stack and see if I can boost the amperage up a little more..

    Can you tell me if your setup is yielding any fuel savings ?...
  9. Replies
    2
    Views
    5,325

    1994 Mitsubishi Pajero 3L V6

    Hi I have a Pajero V6 3L Petrol and I have also been trying to get some savings for ages.

    I have no problem leaning the engine since I can run with the O2 unplugged and I have a small computer...
  10. Replies
    8
    Views
    9,784

    Firstly you should hook up the generator to relay...

    Firstly you should hook up the generator to relay that is powered from your fuel pump or oil pressure switch. This is the most basic minimum safety feature. There should be no possibility at all that...
  11. Replies
    97
    Views
    62,244

    What you are saying makes sense I guess, but how...

    What you are saying makes sense I guess, but how do you explain my sudden loss of power when running at 20Amps ?

    I can try it again...
    I remember that when I tried it was night and it was...
  12. Replies
    97
    Views
    62,244

    Guys, I have had only 1 to 10% savings on and off...

    Guys, I have had only 1 to 10% savings on and off on a 3.0L v6 pajero/montero.

    I have been talking to Les who authored the D17 efie document. He says that steam is bad. Water is ok because it can...
  13. Thread: AFR for HHO

    by jbalat
    Replies
    1
    Views
    3,303

    Guys I tried 15.3 with really bad results. I have...

    Guys I tried 15.3 with really bad results. I have adjusted the cruise AFR to 16.3 and its looking much better


    Is there anyone out there actually getting savings with HHO ?

    :confused:If so...
  14. Thread: AFR for HHO

    by jbalat
    Replies
    1
    Views
    3,303

    AFR for HHO

    From a bit of surfing I found that 14.7 is good for idle and 15 is good for best torque at best economy (under normal loads) while 13 is good for power

    How does this translate for HHO ?

    I just...
  15. Replies
    1
    Views
    4,767

    I have made a frequency modifier using a...

    I have made a frequency modifier using a propeller chip and fitted it to my pajero. I unplugged the O2 so it cant adjust the mixture back.
    It works with an adjustable pot but I still cant get any...
Results 1 to 15 of 19