Search:

Type: Posts; User: hhotb

Search: Search took 0.00 seconds.

  1. Thread: Neoprene Gaskets

    by hhotb
    Replies
    3
    Views
    9,168

    Neoprene Gaskets

    how hard should the gaskets be? i have some neoprene with durometer rating between 55-65. is this good enough?
  2. Thread: Reservoir

    by hhotb
    Replies
    11
    Views
    31,510

    how would i go about doing that? could i just cut...

    how would i go about doing that? could i just cut a circle out of a neoprene gasket?
  3. Replies
    23
    Views
    15,826

    im also trying to find the right amount to "idle"...

    im also trying to find the right amount to "idle" without any gas and the rpm can be increased by adding gasoline. i dont know how to calculate it but i do know that BioFarmer is right. use his set...
  4. Thread: Reservoir

    by hhotb
    Replies
    11
    Views
    31,510

    Bottle, cap, shipping, $15. $15 saved

    Bottle, cap, shipping, $15. $15 saved
  5. Thread: Reservoir

    by hhotb
    Replies
    11
    Views
    31,510

    thanks that got me right where i wanted. ...

    thanks that got me right where i wanted.
    http://www.usplastic.com/catalog/item.aspx?itemid=46228
    this is the one i picked out
  6. Thread: Reservoir

    by hhotb
    Replies
    11
    Views
    31,510

    ya i dont need all that. i can drill and thread...

    ya i dont need all that. i can drill and thread my own holes and mount with my own brackets. and shape doesnt really matter to me. all i need is the translucent tank with an air tight cap.
  7. Thread: Reservoir

    by hhotb
    Replies
    11
    Views
    31,510

    Reservoir

    im looking for a cheap reservoir or container that i can make into an effective reservoir. $30 is just to much for a plastic tank. i thought PVC but im not sure how the shape will affect the gravity...
  8. Thread: Neutral plates?

    by hhotb
    Replies
    7
    Views
    7,496

    If i were to add a second stack to make it + N N...

    If i were to add a second stack to make it + N N N - N N N + would that pull the same amps and create only a small amount more heat but produce more gas (if i were to be supllying to a larger engine)?
  9. Replies
    4
    Views
    6,472

    i figured if i use multiple stacks i can reduce...

    i figured if i use multiple stacks i can reduce the heat. i can run my dry cell for hours and hours on end without nearly as much heat as SS. and the amount carbon collecting at the bottom is minimal...
  10. Replies
    4
    Views
    6,472

    you might want to do some research. look at a...

    you might want to do some research. look at a reaction table. its a good substitute to titanium
  11. Thread: Neutral plates?

    by hhotb
    Replies
    7
    Views
    7,496

    thanks so much. that answered a lot more than i...

    thanks so much. that answered a lot more than i expected. so if im looking to get under .5 amps/sq. in. how can i adjust the amount of amps? would the number of stacks or number of plates effect this...
  12. Thread: Neutral plates?

    by hhotb
    Replies
    7
    Views
    7,496

    Neutral plates?

    Why would neutral plates produce more gas? wouldnt the larger distance from + to - increase resistance, and on top of that you add dead plates? to me it sounds like production would decrease greatly....
  13. Thread: 316l vs graphite

    by hhotb
    Replies
    1
    Views
    8,270

    i have been using carbon rods out of a lantern...

    i have been using carbon rods out of a lantern battery. i have noticed an increase of production compared to SS. my first dry cell i plan on building with graphite plates
  14. Replies
    4
    Views
    6,472

    New Electrode idea?

    I've been playing around with carbon rods lately and im hoping to make my first dry cell with 1/4"x4"x4" graphite plates. they are fragile but they absorb the heat, dont react with KOH or HHO, and...
Results 1 to 14 of 14