Search:

Type: Posts; User: danntanna

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    3,688

    pictures

    here are some
  2. Replies
    34
    Views
    24,866

    carburators

    Hi just finished installing my generator in my 72/56 willys truck.It's a 56 willys truck body on the frame of a 72 chev pu.I have kept the drive train from the 72 for convienence sake.So I have a...
  3. Replies
    10
    Views
    9,005

    ignition

    Hey,So I just switched from a ignition with points to an electronic ignition.Nothin fancy just basic HEI.My engine is a straight six 4.1 liter.I know I need 2lpm for my engine just not sure how much...
  4. Replies
    10
    Views
    9,005

    P.S.

    Check out everything on HHO connections website.Thats what has helped me the most.
  5. Replies
    10
    Views
    9,005

    Same boat

    It's been a bit difficult to figure out what size and configuration will work best.I started with a small dry cell pos neg 5 nuetral.I know this cell does not produce enough hho for my truck.I also...
  6. Thread: Hopeful

    by danntanna
    Replies
    0
    Views
    2,554

    Hopeful

    So I installed a gen. in my truck a while ago.About two weeks.Anyway I left one post since.I had no gain in milage what so ever.Then the truck started to run really rough.Needless to say I was a more...
  7. Thread: some results

    by danntanna
    Replies
    6
    Views
    6,558

    So i figure this is as good a place as any to...

    So i figure this is as good a place as any to post progress.After a small amount of bench testing and experimentation I reduced the size of my generator.It is now 6 nuetrals 7 cells.It seems to be...
  8. Thread: plate count

    by danntanna
    Replies
    9
    Views
    7,662

    Thanks got it sorted out.Note to self don't...

    Thanks got it sorted out.Note to self don't forget to turn the switch on volt meter.0 to 10 10 to 50.Hmmmmm.Thanks again
  9. Thread: plate count

    by danntanna
    Replies
    9
    Views
    7,662

    More photos.The blue jar is water injection.Not...

    More photos.The blue jar is water injection.Not part of the reactor.
  10. Thread: plate count

    by danntanna
    Replies
    9
    Views
    7,662

    Do you think there is anyway the mirror stainless...

    Do you think there is anyway the mirror stainless could be helping with production?Allowing the gas to escape faster.It sure doesn't stay in the cell long.If all this is correct this means I should...
  11. Thread: plate count

    by danntanna
    Replies
    9
    Views
    7,662

    Also one side has a bit better production than...

    Also one side has a bit better production than the other.
  12. Thread: plate count

    by danntanna
    Replies
    9
    Views
    7,662

    Correction 16v

    Correction 16v
  13. Thread: plate count

    by danntanna
    Replies
    9
    Views
    7,662

    just double checked everything some pics also.The...

    just double checked everything some pics also.The brown tint is because its sitting on a piece of discolored plywood.Thanks
  14. Thread: plate count

    by danntanna
    Replies
    9
    Views
    7,662

    I'm getting @ 15v at the cell seems wierd to me...

    I'm getting @ 15v at the cell seems wierd to me also unless I have stumbled onto something.I'm using 304 mirror stainless.I'm getting no percipitate.The catalyst is clear.Not sure what solution...
  15. Thread: plate count

    by danntanna
    Replies
    9
    Views
    7,662

    plate count

    I have my first dry cell done .Seems to work great after some experimenting and advise from you guys.Heres the design.+nnnn-nnnn+nnnn-.My question is this.I hear that maximum performance is with a...
  16. Thread: some results

    by danntanna
    Replies
    6
    Views
    6,558

    After some thought I'm going to take your...

    After some thought I'm going to take your suggestion and remove the small stack.I keep thinking more would be better but I know thats not the case.Efficiency is what I'm going for.Thanks
  17. Thread: some results

    by danntanna
    Replies
    6
    Views
    6,558

    Thanks Larry I was hoping someone would answer my...

    Thanks Larry I was hoping someone would answer my question about number of plates.Well ok I didn't really ask a question.Would it be better to add one or subtract three?And thanks again for all the...
  18. Thread: *****in

    by danntanna
    Replies
    1
    Views
    4,236

    *****in

    Here are some photos so you guys don't think I'm a liar
  19. Replies
    4
    Views
    21,035

    don't laugh it works great

    PWM off a blinking arrow.
  20. Thread: some results

    by danntanna
    Replies
    6
    Views
    6,558

    Success this cell functions perfectly no brown...

    Success this cell functions perfectly no brown sludge.Gonna condition it for a few hours then see what it'll do as far as LPM.Thanks to all you guys for the help.can't wait to get it installed.
  21. Thread: some results

    by danntanna
    Replies
    6
    Views
    6,558

    some results

    Some body stop me I'm obsessed with this technology.I think its because for years Ive been wanting it.Recap.I built a mason jar cell took me about 1 day to get over that.So I was at the steele yard...
  22. Thread: plc

    by danntanna
    Replies
    0
    Views
    3,957

    plc

    Some body should come up with a affordable PLC programable logic comand for us guys it would solve a lot of problems.
  23. Thread: hello again

    by danntanna
    Replies
    8
    Views
    6,858

    Thanks Larry I can relate.In my First video we...

    Thanks Larry I can relate.In my First video we are filling one liter bottles with hho and sending them up.How silly is that.Just to excited about the whole idea of hho.Like a kid.May have to delete...
  24. Replies
    1
    Views
    3,528

    point of interest

    I was just talking to a guy that used to sell fitness equiptment.He told me that tread mills contain dc PWM's probably alot of other usable stuff.
  25. Thread: hello again

    by danntanna
    Replies
    8
    Views
    6,858

    Hi the above mentioned setup is correct but not...

    Hi the above mentioned setup is correct but not correct +nnnnnnn-+nnnnnnn-+nnnnnnn- now I see my error don't know why I didn't before.I'll change it tommorow.Keep ya posted.Thanks guys
Results 1 to 25 of 39
Page 1 of 2 1 2