Your inlet should be at least 1" above the gasket edge.
The outlet should be as close to the gasket edge as possible. also note the outlet holes(s) should be larger than the inlet hole.
It is...
Type: Posts; User: Bhart
Your inlet should be at least 1" above the gasket edge.
The outlet should be as close to the gasket edge as possible. also note the outlet holes(s) should be larger than the inlet hole.
It is...
Mike,
I will try to answer your questions with my own experience or what I have researched.
Either electrolyte will work, I use the KOH as I can get it at Ace Hardware as LYE.
As far as...
Mike,
Check out http://www.youtube.com/user/hhoconnection
Mike has several videos on HHO and it should help in answering a lot of your questions.
I have used gorilla glue on the fitting with success.
Why stop at two alternators
http://www.youtube.com/watch?v=2pQeeUkPoyk&feature=youtu.be
http://www.youtube.com/watch?v=2pQeeUkPoyk&feature=youtu.be
Where ever you have the room, if it fits in those locations use it. I have a 1997 k1500 Chevy and I put my first bubbler between the radiator and the fan.
Best set-up would be to have every thing...
The primary reservoir that feeds the secondary reservoir is higher than the cell so it would keep the electrolyte level in the cell full.
Replace your air intake shrouding and let your engine get its air through he engine compartment instead of the all the duct work through the fender. This will free up enough space for your reservoir...
Here are two sites to get you started on HHO:
http://www.panaceauniversity.org/Hydroxy%20Boosters.pdf
http://www.panaceauniversity.org/GEET%20fuel%20procesor.pdf
228Robinson, be aware of federal law that prohibits any changes to any emission device, ECU, O2 sensors, etc. Could be a $2500 fine, that could be embarrassing for a police department.
You can get a 1lb. container of NaOH from ACE Hardware for just under $5.00.
That is a good resource for assembling a HHO reactor, but the small hole should be staggered from plate to plate as far apart as possible and 1 1/2" to 3"from bottom of active plate area. The...
I did a similar experiment and my battery posts got red hot from the amp draw.
They have had only one review and that was a negative one. Are you sure you want one of these?
Warranty issues July 29, 2010
Reviewer: Anonymous person from United Kingdom
PWM failed ...
Ask for Lye it is used as drain cleaner. I get NaOH at Ace Hardware for $4.60 a lb container. Be sure to get 100% Sodium Hydroxide. Lowes also has a product but it was twice as expensive.
You...
I have a 1997 Chevy K1500 with the 5.7 vortec engine. I ran the Volo FS2 for about one year and it did not make a difference in my mileage. I will be setting up an efie with a pwm later this week....
Are the VAFC1 set up for particular makes of vehicles like the Volo are, or can they be used for any make of vehicle.
I did a Craig's list for my state (Colorado), California, Texas, New York, Pennsylvania, New Jersey, and the cheapest was $150 but most were $250 and above. I must of done 100 searches.
Your 1/4" acrylic will crack at the mounting holes. It is too thin, some builders use plastic cutting boards. You will need to offset your inlet holes so they are not in line with each other...
Have you done a google search for HHO dry cell plans? I used the plans from Tom Punch and made modifications to my specifications.
http://www.drycellplans.com/drycellindex.php
What is wrong with KOH or NaOH, when it leaks all over the inside of the engine compartment it really shines everything up it a great caustic cleaner!!!! Anyone......
Bazarom, I have a three inch diameter bubbler that is 12" long. I feed my HHO into the bubbler from the top side. From that fitting I have a coiled tube that is 6' long that fits inside of the...
Jeremy, do not hook your electrical to the ignition switch!!!!
This is also a big no no!!!! Once the the switch is turned on you are making HHO whether your engine is running or not. If the...
I got Weldon-16 at ebay for $17.00 + 7.95 for shipping.
Seller was ROSS BROUGH, his email is:
piperplastics1@yahoo.com
Glad you came back here Larry. I hope you continue to enlighten us on your Beastie when you are able to get back to it.