I got my own dry cell that works pretty well, still minor leaks but that will get fixed later on.
And i do have a gain in MPG so i would like to keep this.
Problem is i am honestly getting tired...
Type: Posts; User: viper_1986_1986
I got my own dry cell that works pretty well, still minor leaks but that will get fixed later on.
And i do have a gain in MPG so i would like to keep this.
Problem is i am honestly getting tired...
So get this, funny enough on my timing.
But while working today as i hit 100 miles my engine randomly died, i turned it back on with CEL....
Had it checked out and i have a lean fuel mix!
I...
I knew that people said it cleaned out the engine, but didn't think it would affect it that much.
And no EFIE or O2 enanchers yet.
Those are on hold until i can save up so more money.... 8$/hr +...
So i have a 2000 ford focus 2.0 DOHC with 167,000 miles on it.
We will say my HHO cell makes around 2lmp and created a bit of vapor. I was lacking a bubbler/scrubber but still ran with it for quick...
I also had this issue when going throw a 2nd bubbler.
It doesn't seem to have ANY leaks but the production is cut in 1/2 or so.
Going right from cell to a water jug i get that pretty 2lmp or so on...
2000 Ford Focus 2.0 DOHC zx3
I have my HHO project on hold right now as skydiving just took all my money
:{ Will be doing lots more reseach on this stuff.
I am sure i need it.
For now i have...
No need for all those Qs...
Just an answer for his question.
It is cause too many amps are running through the fuse :D
No really, answer all the above questions.
Off the top of my head my...
And i will take your word for it, a MAF enhancer is for fine tuning.
I won't question or wonder why, ill just believe you :D
Now to find a EFIE that i like and will work for my car!
and thanks...
So i am a bit unclear on what each does and when you should use one or both.
My current belief is EFIE controls the O2 sensor as it goes into the computer, so it can lean/raise the fuel mix?
...
Just to note, i have a bubbler/res.
NO bubbler/scrubber.
Is that ok to do the 50/50 mix in?
I do plan on getting a 2nd bubbler just not yet :)
I know that using KOH and KaOH the steam is true H2O, no KOH or KaOH is in it, correct?
If that is true then a bit of water vapor will not effect the engine in a bad, way, if anything, it will be...
I couldn't find such a thing on google.
Best bet is to just order one from some american site and have it shipped over.
It will cost you a bit but... what else can you do :D
Maybe you can find...
Caught my eye on that....
I have been using my father's drill press to do my holes and i already killed a few of his bits...
I kinda figured to do SUPER low RPMS....
But.... Brake fluid? Like...
Heh i guess thats in a safe spot :D
I can see someone putting it in the tail end of the truck and then getting rear ended :D
That is ONE nice setup too.
I plan on making one for my father's 92...
My rad res kinda leaks.
Those little nipples that have the ball were the issue. The molding seem was HUGE and my tube was not getting a good fit, even with clamps.
So just used a bit of sand...
I wish i had my first cell :{
I used the cover plates from an old computer. After a few hours of using them they turned into a greenish goo and disapeared into my water....
My next wet cell from...
Well I figured I would post my results and findings here as a way to log everything and share it with everyone.
Just to start off i WON'T be doing any "TRUE" mileage tests as i am not going to...
Bathroom handle bar pipes work good from my little test.
Its just a pain to fine the smaller/larger size since there is a stanard most people use that i guess....
I went around to business that...
I have only some very small scrap pieces left so i can't try the saw, but next time i get my hands on a large piece i will try it again. The blade i was using was very unstable :D
The very end of...
It is good to learn what it can do.... i rather have a controlled BOOM and see the effects rather than an accident.
But look at some youtube videos, my personal favorite are......
Depending on its gauge you can easily cut it with just some elbow grease :)
Just bending it back and forth.
Get a GOOD first bend using some clamps and make sure its dead on; then evenly across the...
Once i couldn't view it from my friends house.
The site doesnt have much info on its whois, just the domain name hosting is verisign....
Seems rather odd.
I have a feeling the site is hosted...
I attempted EGR valve, too much suction, less than PCV but still way to much.
Best to get the HHO in into the airintake AFTER the MAF/MAP sensor.
Even if it means drilling into it :{
...
Using - + - + you will draw alot of amps and quick.
Best to use the N plates... to keep the volts down. HHO will be created with as little as 2 volts, i think it can even be lower.
Using a wet...
Yes from my first wet cell i made i have learned brass doesn't stay very brassy for too long.....
Also yes, its rubber coming from the throttle body, i got a AEM SRI....
Ok thanks for the help...