Search:

Type: Posts; User: Sniper168

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    3,141

    High Duty Cycle

    I know this issue HAS to have been covered here already but the search engine doesn't bring anything up at all !
    Basic Facts:
    '05 Nissan Pathfinder
    V6 4.0 L 4x4
    Factory MPG = 13/19
    HHO MPG =...
  2. new unit

    I thought I might have a leak somewhere amongst all my other problems, so I removed the unit all together and started anew.
    I'm now using the Smack's Booster (4" diameter pvc tubing, etc) and...
  3. anyone? help....

    Ok so I posted the video....and no feedback.
    I would also like to know where I should install this one way valve...AND...where I am supposed to get this one way valve at?
    Like a fish aquarium one...
  4. flash arrester + one-way valve

    Ok, so I figure I need to add a flash arrester immediately after the the HHO device and immediately before the bubbler, Right?
    I am also wanting then to install a one-way valve somewhere between the...
  5. Video

    Alright Ladies and Gentlemen. Time now for the main event.
    Please, no eating or drinking while watching this video as the owner cannot be held liable for any seizures or choking which may occur...
  6. I don't have a resevoir at all. I'll take picks...

    I don't have a resevoir at all. I'll take picks of my device when I get home, but in a nutshell, the HHO comes out the top of the chamber in a 1/4" ID tube and runs down to the bottom of the Bubbler....
  7. Readings and Efficiency not quite right....

    Ok. So I've gotten everything installed and have been running the HHO device for about 3 weeks now.
    First few runs:
    Well, I didn't read all the way through the paperwork and learned the hard way...
  8. Replies
    24
    Views
    19,901

    Flashback arrestor

    Thanks for all the advice gentlement - especially your patience Steve.
    Now, onto a final thought; Do I need to install a flash-back arrestor?
    it seems very straight forward to make and install, but...
  9. Replies
    24
    Views
    19,901

    ok...

    Ok, I set the multimeter on the "2" under the DCV category.
    I plugged the red and bl
    ack posted into the EFIE then started the car.
    Sure enough, just as the instructions indicated, the beginning...
  10. Replies
    24
    Views
    19,901

    Ok so here's where I'm at. I set my multimeter to...

    Ok so here's where I'm at. I set my multimeter to the 200m setting and was getting a reading from 200 to 0 (or close to 0 I think). Anyway, my instructions said that I should start out at 350mv and...
  11. Replies
    24
    Views
    19,901

    I bought a new multi-meter and wouldn't ya know...

    I bought a new multi-meter and wouldn't ya know it, I can't for the life of me figure out how to get the readings that the paperwork is telling me I'm supposed to be getting.
    THe paperwork said I'm...
  12. Replies
    24
    Views
    19,901

    I'm sorry gents

    Look, I want to thank you all for entertaining my stupidity. I pulled out the papers that I downloaded and when I bought all this stuff and what do you think I found... but the freakin' directions on...
  13. Replies
    24
    Views
    19,901

    hmmmmm.... and how do I do this? lol

    hmmmmm.... and how do I do this? lol
  14. Replies
    24
    Views
    19,901

    Trying to understand....

    I'm new to your forums as well as HHO making, so bear with me. I just guilt a smack's booster with bubbler.
    I have the following setup:
    1) + wire coming from Fuel pump relay
    2) this goes to 40amp...
  15. Replies
    2
    Views
    4,266

    Engine Light keeps coming on

    I have just installed the EFIE (Dual Digital) and CCPWM from a company called Dry-Cells. Everything appears to be hooked up properly as I'm making HHO and getting good gas mileage.... until that is I...
Results 1 to 15 of 15