Search:

Type: Posts; User: Havens78

Page 1 of 7 1 2 3 4

Search: Search took 0.02 seconds.

  1. I am simply answering to the best of my knowledge...

    I am simply answering to the best of my knowledge based on the experiences that I have seen while experimenting. I do not claim to have all of the answers or do I claim to know what is happening to...
  2. I do not know of a cheap unit but I know of a...

    I do not know of a cheap unit but I know of a good wide-band unit that works very well.
    ...
  3. Replies
    8
    Views
    36,637

    20% NaOH is what i use, and no its not toxic if...

    20% NaOH is what i use, and no its not toxic if you scrub it out of the gas well enough.
  4. You are producing too much gas from your kit, the...

    You are producing too much gas from your kit, the 2nd o2 sensor is reading the extra oxygen and is telling your honda that it is running lean. Your engine will fix this by pushing more gas down its...
  5. Replies
    6
    Views
    26,167

    If by bubbler you mean scrubber after the...

    If by bubbler you mean scrubber after the electrolyte tank then you want a system large enough to scrub the electrolyte out of the gas. If you are using a dry filter you want probably a 6"-12" long...
  6. Replies
    1
    Views
    24,323

    I wish everyone who asked me about HHO was trying...

    I wish everyone who asked me about HHO was trying the techniques you are having luck with already. But the short answer is that HHO is not simple and anyone that tells you they can sell you...
  7. Replies
    5
    Views
    7,899

    With only 3 neutrals you are going to be making...

    With only 3 neutrals you are going to be making more steam than hho, your fuse more than likely blew due to thermal runaway. You will have better production with 7 plates in your configuration and 1...
  8. Replies
    4
    Views
    9,579

    EPDM 45 mil pond liner is what I use. Stack...

    EPDM 45 mil pond liner is what I use. Stack gaskets to get the desired spacing that I want. I think you can get 25 sq. ft. online for $25 US. I have used this material in many dry cells and never...
  9. Replies
    2
    Views
    7,081

    What concentration is your electrolyte at, did...

    What concentration is your electrolyte at, did you keep it the same as before when it was only +5n-?

    Can you measure the voltage between the plates? This needs to be between 1.9 and 2.3 volts...
  10. Replies
    1
    Views
    9,775

    In my experience with buying full kits, you need...

    In my experience with buying full kits, you need to look at what they are offering for your specific need.

    -What kind of filtering system are they using to keep the KOH or NaOH out of your...
  11. Thread: car battery

    by Havens78
    Replies
    4
    Views
    6,725

    I have used a charger hooked to a battery and...

    I have used a charger hooked to a battery and then powered a reactor from the battery, though I never could get more than 12.5-13 volts running 15 amps. So if you plan to only use small amounts of...
  12. Replies
    8
    Views
    9,871

    First I'd like to ask what your goal is, because...

    First I'd like to ask what your goal is, because there are a lot of things wrong here with your setup. My first suggestion is to turn it off and do some reading in the general forum section. But...
  13. Replies
    6
    Views
    8,138

    Can you provide any pictures at all of your...

    Can you provide any pictures at all of your plates and setup? This would help us to help you. Also you need at least 1.8volts per plate-gap, you need more voltage.
  14. Do a search for bubbler design and you'll find a...

    Do a search for bubbler design and you'll find a way to build one that won't let water travel to your intake.

    Your reactor needs to be the lowest point in the system if you're not going to run a...
  15. Replies
    9
    Views
    8,343

    I wouldn't suggest having fewer than 5 neutrals...

    I wouldn't suggest having fewer than 5 neutrals per stack in your setup in order to keep the voltage around 2.25v per plate gap. too much voltage will create more steam than hho. Even if you have to...
  16. Replies
    3
    Views
    5,098

    If you filter your gas output correctly no...

    If you filter your gas output correctly no electrolyte will even get close to the aluminum parts of your engine. Do a search for 'bubbler' and see what shows up, there are some very good designs that...
  17. I have seen more consistent results with a manual...

    I have seen more consistent results with a manual enhancer, but they are more complicated to tune and take more patience. The VOLO is cheap and easy and works for some people and not for others, but...
  18. Replies
    4
    Views
    4,979

    How large is your reservoir? Do you have the...

    How large is your reservoir? Do you have the ability to change your neutral plate count to 5 between each power plate? This will reduce the voltage between the plates and help to keep the heat...
  19. If you follow the filter/setup advice that you...

    If you follow the filter/setup advice that you will find in the older posts on this forum you won't have any negative effects on your engine. If you try to not research what you're doing and not...
  20. Replies
    38
    Views
    95,725

    More HHO doesn't mean more mpg gain, You have to...

    More HHO doesn't mean more mpg gain, You have to use the amount that is optimal for your vehicle. Normally that is calculated at .5 lpm for every liter of engine displacement in gasoline vehicles...
  21. Can you provide any information about the reactor...

    Can you provide any information about the reactor you used, how many amps were being drawn by the unit while it was installed and if you had any voltage issues with the car when the HHO was running?...
  22. Replies
    2
    Views
    7,755

    Welcome to HHO, unfortunately you have found that...

    Welcome to HHO, unfortunately you have found that not all of these kits are equal and service after the sale can only be so great. I have installed and repaired a 773 kit from transitional...
  23. Replies
    6
    Views
    7,122

    First I would ask what your gasket thickness is,...

    First I would ask what your gasket thickness is, the greater the thickness the stronger % of electrolyte you usually will need. Secondly can you measure the voltage that you are getting at your...
  24. Replies
    31
    Views
    22,201

    For an update this bipolar reactor is working...

    For an update this bipolar reactor is working very well. I reduced it to one stack for my 2.5 liter engine and even with 1/16" gaskets it is running better than I expected it to. The mmw rating...
  25. Replies
    2
    Views
    5,396

    You will need to start with 1/2 a liter of Gas...

    You will need to start with 1/2 a liter of Gas per minute per 1 liter of engine displacement, and you want to start with 15 amps per liter of gas. So for 2 liters per minute you would need at least...
Results 1 to 25 of 167
Page 1 of 7 1 2 3 4