Search:

Type: Posts; User: YFZR750

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    19,738

    Tube Electrode spacing.

    Good Day,


    I would like to build a generator with the same design of Stanley Meyer. (Stainless Steel tubes)

    But I am puzzled on how to get the tubes spaced reliably without having them touch...
  2. Replies
    3
    Views
    28,868

    Electrolysis Of Steam

    Hi guys,

    Was wondering if this could be possible?

    If water vapour (steam) could be used as the fuel.

    I have tried to measure the continuity of the steam and have found that it has zero. But...
  3. Replies
    7
    Views
    24,869

    Hi, I will do the research and see what comes...

    Hi,

    I will do the research and see what comes up.

    And Thanks for the help Retro!
  4. Replies
    7
    Views
    24,869

    Okay, I was doing a bit of research and found...

    Okay, I was doing a bit of research and found that instead of the voltage splitting the water, it is actually jumping to the next tube.

    So I am thinking, use 2 coils. One for the positive tube...
  5. Replies
    7
    Views
    24,869

    Hi, I have read through those threads but I...

    Hi,

    I have read through those threads but I could not find a good explination.

    I find it very puzzling that there is zero bubbles, not even a mist. But connected to a car battery it produces a...
  6. Replies
    7
    Views
    24,869

    Hi, Okay. That answered my question, but I...

    Hi,

    Okay. That answered my question, but I have another.

    I created a test cell replica of stanley meyer, 1.5mm gap between the tubes at each side. So a total clearence of 3mm.

    I connected it...
  7. Replies
    7
    Views
    24,869

    Bifilar Inductor ?

    Hello,

    I have searched the net for some discription on what a Bifilar inductor is but I have had no luck. Besides Wikipedia but its way too difficult to understand.

    What does the Bifilar...
  8. Replies
    7
    Views
    9,984

    Hi, I just wanted to ask one last question. ...

    Hi,

    I just wanted to ask one last question.

    Is it possible to run a engine on 100% HHO with stock internals?

    Could retarding the ignition timing and perhaps lower the compression would it...
  9. Replies
    7
    Views
    9,984

    Thanks for the advice, I decided I would rather...

    Thanks for the advice, I decided I would rather go for the single cell hho design with the stainless steel pipes.

    Do you perhaps have experience on having a automotive ignition coil to power the...
  10. Replies
    7
    Views
    9,984

    I know with a single cell unit, the arrangement...

    I know with a single cell unit, the arrangement of having neutral plates lowers the voltage.

    In the HA generator, does the surface area lower the voltage?

    I would be using a 12v 80Amp hour...
  11. Replies
    7
    Views
    9,984

    Okay, so if it is set up with the stainless steel...

    Okay, so if it is set up with the stainless steel pipes in the machine gun arrangement in each tube, would it produce lots of gas ? Around how much would you think?
    And would the amount of pipes in...
  12. Replies
    7
    Views
    9,984

    Hydrogen Generator Design, Advice Needed.

    Hi Guys,


    New to the forum. I found the Hydrogen generators quite interesting so I decided to join.


    I am in need of some advice.

    I would like to build a split cell generator so that I...
Results 1 to 12 of 12