My best configeration so far is Pos nnnnn Neg 8 mm gap Pos nnnnn Neg, .076 inches gap or just under 2 mm. My plates are 80 sq inch each 14 0f them and at 30 volt 140 amp I am producing 10 LPM. If you...
Type: Posts; User: Llew2_1
My best configeration so far is Pos nnnnn Neg 8 mm gap Pos nnnnn Neg, .076 inches gap or just under 2 mm. My plates are 80 sq inch each 14 0f them and at 30 volt 140 amp I am producing 10 LPM. If you...
What I am doing is building in a DC electric welder for my Ford Ute. Going to remove the A/C comprssor and mount it there. This will completely power my HOD indipendantly of the vehicles electrical...
I have 40 hours up bench testing my SS 316, they show no signs of deteriation. It absorbs 30volt 100 amp continious. The plates in my HOD are 80 sq inches each, 14 of them. Making 10 LPM.
Llew
My HOD has 14 plates 80 sq inches each. It won't operate at less than 100 amps and works best at 200 amps. At 30 volts. The HOD holds 22 liters of water, 6 KG KOH ans 1.5 KG of NaOH. Makes about 10...
I have been using mostly caustic soda, tried baking soda not quite as good.
I alway get mixed up with the cemical names.
I am about to run another test tomorrow. A few days ago drawing, 103 amps at...
We have a HOD device, which draws 22 amps. Wich is the max the my charger will put out. It trips out then. It generates lots of bubbles, but not enough for what we want. We are experimenting with a...
Hi Again,
The reason for the large gap, is to match the existing holes in the lid. This time I will make a bracket, to move the neg to match where the stack ends. I have uploaded new pics of my...
Thanks Roland,
I was talking to a guy this morning and he said. I should insulate the negative connection as well has the positive. So then the only electrical connection with the case would be...
I am using the flash back arrestor, that are fitted to Oxy welding torches. Mounted where the HHO enters the induction system.
I have built a HHO gen, 12 in square. The plates are 8 x 10 x ,040 ins, spacings .120 ins. Connected in series -+-+-+ across the stack. 8 pairs of plates. The tank holds 22 litres water, put two...
Thanks Rowland,
Thats exactly what I could not remember, I shall have to use plumbing PVC, but I think it will work fine.
Hi Dodge,
Thats great thanks very much.
Llew
You can separate water from any gas by cooling it, heat exchanger in cooling system. Then a commercial water separator, same as used in paint shops.
From what I know, HHO will do no harm to your engine. But with an old car like that, you do need to keep the valves adjusted properly. 500 miles after the head was off. You need to check the valve...
Does anyone know how to make a simple flow meter and how to calibrate it.
Also does anyone use a " standard water gauge " to indicate pressure in the HHO generator. And how to calibrate it. I used...
Anyone have a design for a simple flow meter. I have a few thoughts.
1) A transperent tube. with a pingpong ball in it, but how to calibrate it ??
2) Submerse a 1 ltr bottle, in a bucket of water....
I have used 100 grams with 10 literes water, works well. After mods I will fill up the generator with 20 literes water. Was pulling 30 amps. No heat.
To day I run my HHO generator for the first time. I was concerned that the SS case grounded to the car would not work. I am using the inside of the case as negative + 2 pairs of plates. The positive...
My experiment is with a SS case 12 inches square. 16 plates 8 x 10 x .040 inches. Each plate is 80 sq inches, spacing is .120 inches Total area is 1280 sq inches plus the inside of the case.
My...
My experiment is with a SS case 12 inches square. 16 plates 8 x 10 x .040 inches. Each plate is 80 sq inches, spacing is .120 inches Total area is 1280 sq inches plus the inside of the case.
My...
I have been recomended by one site, to use Sulphuric acid diluted 5;1 as am elcrolyte. Any one got advive to offer.
Does my heart good to see that old girl, I am 72 yrs old. On the farm we have 4 Falcon Utes and a crane which has a Falcon engine in it.
On the road we have an 86 wagon and a 90 Ute. We have about...
I am about to assemble a HHO generator, it is intended to fit behind the bull bar. I run old Ford Falcons 1986 vintage, converted to run on petrol/LPG.
The case is 12 inches square. All 316 SS, I...