Now THIS is a great example of a KISS (keep it simple stupid) dry cell that has a reduced possibility of current leakage:
As long as the level in the tank is maintained correctly, this should be a fairly effficient cell design!
Now THIS is a great example of a KISS (keep it simple stupid) dry cell that has a reduced possibility of current leakage:
As long as the level in the tank is maintained correctly, this should be a fairly effficient cell design!
Make a square cell out of flat plates with a hole in the upper right corner.
Is there anything more KISS than an Amoeba Cell?
Turn the cell to the left so that the hole is up.
Starve the cell by keeping the reservoir electrolyte level close in height to the hole.
The holes will be mostly dry.
Low leakage.
Perhaps a saving of 8% in efficiency.
So what? The 8% loss is not the issue.
Implementing the Hydroxy and adjusting the ECU is the issue.
Have you tried restricting the air input?
Works for me.
BoyntonStu
Stu,
Please bare in mind when considering efficiency that some of us need larger volumes of gas, therefore, every MMW improvement we can get is a worthy goal. From my research, I need to find between 4-5 LPM of HHO with 40-45 amps of power (max).
4.5 LPM at 45 amps and 14.1v will require an MMW efficiency in the 7's.
I did try restricting the air input, if you remember. A 25% restriction gave no gains over a month or so of testing. I removed the restriction on Monday and my engine is running smoothly again, the lumpy idle has gone and the sudden cutouts too (although the cutouts could have been electrical). My conclusion, air restriction may not be favourable for the newer models.
For me, MMW efficiency is more than a "look what I can do", it's a required goal.
My scantool shows no change at 2.5 LPM of dry HHO. I had a long one-on-one chat with Rob from highpoweredh2o a couple of weeks ago, he has a lot of experience with installs in different vehicles. He quoted for my 4.7L:
For dry HHO (vapour condensed out, like mine) you will need upwards of 8 LPM to see good gains.
For wet HHO you will need approx. 4 LPM upwards.
I suggested that I combined 4 LPM with water vapour injection, he was very enthusiastic about that idea. I've read that 5% water to fuel is an ideal ratio.
I can't help but think that a lot of people with the larger V8's are actually seeing gains purely through leaning and not as a result of the HHO. This is why I insisted on an EGT gauge.
Which motor does your Ram have? Hemi? Where is your injection point?
Russ.
I have a 2006 Dodge Ram 1500 with Hemi and automatic. I deliver HHO at the air box about two inchs from the MAS. I've really been thinking about the best way to deliver HHO to my engine. Maybe a tube with a venturi for HHO by the filter. After reading some of your stuff I did drill two 2 1/2 in holes on the engine side of my filter box. What I'm doing now is slaving a pwm to a master pwm to drop actual amperage down by 50%. I'm sure most poeple know that with one pwm, whenever the pwm conducts you still use the same amperage as DC operaton. With an inverter or transistor switch I can make one pwm a slave and make one pwm conduct on the first 50% of the duty cycle and the slave conduct of the last 50% of the duty cycle. This will work for me since my generator is +NN(A)NN-NN(B)NN+NN(C)NN-NN(D)NN+. I can run A & B cell blocks first and C & D cell blocks last during each duty cycle. I might need to add two more cell blocks and I'm wondering if a 30% pulse width would be enough. I could configure for three pwm's though. I enjoyed reading your entire thread.
Russell
So, we pretty much have the same truck except for the engine. You might want to try delivering your HHO into a T in the vacuum and see if that makes any difference, but you will need a ball valve of some kind unless your reservoir is extremely sturdy.
I personally think the combination of 4-5 LPM of HHO and water vapour injection is the best path for us to take. I've thought long and hard about how to make water injection work well, I've tried vacuum but cannot get much draw at all. I'm thinking that some kind of misted spray is the answer.
If you don't use vacuum, you definitely need to feed the HHO right up to the throttle body. The resonator box causes too much air turbulence and I really want to find some appropriate flexible pipe and do away with mine.
Today, I went to lowes and bought some pvc tubing to build a new reservior and I found a great test seal for 2" tubing that should make a great cap for my reservior. Its just a rubber stopper with plates on both sides a screw in the middle and a large wing nut on top. Works good! It might even be a good safty device on a bubbler.
I'm not to sure about using vaccuum just yet. I'll probably try the tube first.
Russell