For any of you wanting to try 430 stainless please read this article. The people trying to sell it are either mis-informed or trying to male an extra buck because it is less expensive.
http://bbq.about.com/od/stainlessste...a042305a_2.htm
For any of you wanting to try 430 stainless please read this article. The people trying to sell it are either mis-informed or trying to male an extra buck because it is less expensive.
http://bbq.about.com/od/stainlessste...a042305a_2.htm
First of all, I would like to say that I do not use 430 grade stainless, but
I do want to point out a fact that does not seem to be apparent throughout this thread, or even through out the forum..........
Rergardless of what plate grades you use (at least in a wet cell design), they need to be connected to the source of current..........
When is the last time you found 430 SS grade nuts and bolts, or for that matter, 316 nuts and bolts (either regular, or L grade)?
In virtually every circumstance (in the USA), you will encounter 18-8 ss nuts, and bolts (which is the same as 304 grade).
Whenever you use two different grades of materials, either above or below the water line, the weaker grade, will always corrode!
However, if you select your plate materials, with the fastener grades in mind, you can yoke the materials evenly!
With no imbalance of material grades, even the softer materials can last a very long time!
But without that balance, even the 316L, will react with the softer bolts, eating away at the connection points of contact, possibly causing a spark!
It is always the softer metal that is eaten up, but materials in balanced composition, do not suffer that consequence!
In the HHO quest, never mix material compositions!
For larger photos of offerings see:
http://shuttermotor.tripod.com/id12.html
Maybe I am lucky but we usually have less variety in Alaska. 316L allthread, nuts, and washers were easy to come by at the local fastener supply store.
In Alaska, that does not surprise me, as the climate there, dips to extreems almost beyond our imaginations. It only makes sense, in such climates to use superior metals, to hold up to brittle cold conditions.
But as a resident of Naples Florida, 316 L hardware, is virtually impossible, to find.
It's no secret, that your climate, requires metals that can out perform most! But that is not the norm.
Store owners have to put out huge amounts of cash, to stock store shelfs, and in the lower 48, spending twice as much, for higher grades of stainless, in most cases, does not make practical sense.
Stainless, in most cases is not required for strength, near as much, as it is for it's non corrosive properties.
Higher carbon content, gives it better strength, which stands up to the "brittle" cold, better.
I don't say that to be argumentitive, but to state that in terms of Alaska's, and Florida's climates, neither of us, can claim to be the normal atmosphere!
In fact, our country is so large, that each specific state varies to some degree, in climate conditions.
For larger photos of offerings see:
http://shuttermotor.tripod.com/id12.html
I have come up with a price chart using 20g. 316 s.s.
You choose the width and height, numbers of holes, and get an instant price.
I will e-mail this chart to anyone interested....
Hello Gents and Ladies! I was wondering if anyone has tried AL-6XN Stainless steel? It has greater corrosion resistance than 316L. It also has higher levels of nickle which means low magnetic characteristics. With very high levels of molybdenum which contributes to the high corrosion resistance. It is also supposed to be less expensive than the traditional stainless steels. I believe this alloy was created because of cloride pitting. This alloy eliminates pitting and stress corrosion.
Would like to get a price on 25 plates 8" X 8"?
Please e-mail your price chart to fbmob1@aol.com